Lab9:IGRP,EIGRP,OSPF之间路由重发布。
版权声明:原创作品,允许转载,转载时请务必以超链接形式标明文章 原始出处 、作者信息和本声明。否则将追究法律责任。http://guyun.blog.51cto.com/71128/23884 |
这段时间也不知道自己在忙些什么,一个礼拜了,今天再写点,再不看6月份还怎么考啊/,该实验主要内容:
1)注意有类与无类网络的发布;
2)各种路由协议之间的重发布。
3)R1与R2的S0/0之间为EIGRP,R2的S0/1与R3的S0/0之间为OSPF,R3的回环口为IGRP.
![]() ![]() 具体过程:
Router>en
Router#con t Router(config)#hostname R1 R1(config)#int loopback 1 R1(config-if)#ip add 10.1.1.1 255.255.255.0 R1(config-if)#no sh R1(config-if)#exit R1(config)#int s0/0 R1(config-if)#ip add 2.2.2.1 255.255.255.0 R1(config-if)#no sh R1(config-if)#exit R1(config)#router eigrp 100 R1(config-router)#net 10.1.1.0 R1(config-router)#net 2.2.2.0 R1(config-router)#exit R1(config)#exit R1#show ip route Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, * - candidate default U - per-user static route Gateway of last resort is not set
10.0.0.0/24 is subnetted, 1 subnets
C 10.1.1.0 is directly connected, Loopback1 2.0.0.0/24 is subnetted, 1 subnets C 2.2.2.0 is directly connected, Serial0 3.0.0.0/16 is subnetted, 1 subnets D 3.3.0.0 [90/3015680] via 2.2.2.2, 00:14:25, Serial0 20.0.0.0/16 is subnetted, 1 subnets D 20.1.0.0 [90/3015680] via 2.2.2.2, 00:12:29, Serial0 Router> Router>en Router#con t Router(config)#host R2 R2(config)#int s0/0 R2(config-if)#ip add 2.2.2.2 255.255.255.0 R2(config-if)#clock rate 64000 R2(config-if)#no sh R2(config-if)#exit R2(config)#int s0/1 R2(config-if)#ip add 3.3.3.1 255.255.0.0 R2(config-if)#clock rate 64000 R2(config-if)#no sh R2(config-if)#exit R2(config)#route ospf 200 R2(config-router)#net 3.3.0.0 0.0.255.255 area 0 R2(config-router)#exit R2(config)#route eigrp 100 R2(config-router)#net 2.2.2.0 R2(config-router)#exit R2(config)#exit R2#show ip route Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, * - candidate default U - per-user static route Gateway of last resort is not set
2.0.0.0/24 is subnetted, 1 subnets
C 2.2.2.0 is directly connected, Serial0 3.0.0.0/16 is subnetted, 1 subnets C 3.3.0.0 is directly connected, Serial1 R2#con t
Enter configuration commands, one per line. End with CNTL/Z. R2(config)#route eigrp 100 R2(config-router)#redistribute ospf 200 metric 1000 100 100 100 100 R2(config-router)#exit R2(config)#route ospf 200 R2(config-router)#redistribute eigrp 100 R2(config-router)#redistribute igrp 100 R2(config-router)#exit R2(config)#exit R2#con t R2(config)#route eigrp 100 R2(config-router)#redistribute ospf 200 metric 1000 100 100 100 100 把OSPF发布到EIGRP R2(config-router)#exit
R2(config)#route ospf 200 R2(config-router)#redistribute eigrp 100 R2(config-router)#exit R2(config)#exit R2#show ip route Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, * - candidate default U - per-user static route Gateway of last resort is not set
3.0.0.0/16 is subnetted, 1 subnets
C 3.3.0.0 is directly connected, Serial1 2.0.0.0/24 is subnetted, 1 subnets C 2.2.2.0 is directly connected, Serial0 10.0.0.0/24 is subnetted, 1 subnets D 10.1.1.0 [90/1628160] via 2.2.2.1, 00:02:08, Serial0 R2#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, * - candidate default U - per-user static route Gateway of last resort is not set
3.0.0.0/16 is subnetted, 1 subnets
C 3.3.0.0 is directly connected, Serial1 2.0.0.0/24 is subnetted, 1 subnets C 2.2.2.0 is directly connected, Serial0 10.0.0.0/24 is subnetted, 1 subnets D 10.1.1.0 [90/1628160] via 2.2.2.1, 00:22:05, Serial0 20.0.0.0/16 is subnetted, 1 subnets O 20.1.0.0 [110/64] via 3.3.3.2, 00:19:53, Serial1 Router> Router>en Router#con t Router(config)#host R3 R3(config)#int loopback 1 R3(config-if)#ip add 20.1.1.1 255.255.0.0 R3(config-if)#no sh R3(config-if)#exit R3(config)#int s0/0 R3(config-if)#ip add 3.3.3.2 255.255.0.0 R3(config-if)#no sh R3(config-if)#exit R3(config)#route igrp 100 R3(config-router)#net 20.1.0.0 R3(config-router)#exit R3(config)#route ospf 200 R3(config-router)#net 3.3.0.0 0.0.255.255 area 0 R3(config-router)#exit R3(config)#exit R3#show ip route Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, * - candidate default U - per-user static route Gateway of last resort is not set
20.0.0.0/16 is subnetted, 1 subnets
C 20.1.0.0 is directly connected, Loopback1 3.0.0.0/16 is subnetted, 1 subnets C 3.3.0.0 is directly connected, Serial0 R3#con t
R3(config)#route ospf 200 R3(config-router)#redistribute igrp 100 R3(config-router)#exit R3(config)#route igrp 100 R3(config-router)#redistribute ospf 200 metric 1000 100 100 100 100 R3(config-router)#exit R3(config)#exit R3#show ip route Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, * - candidate default U - per-user static route Gateway of last resort is not set
20.0.0.0/16 is subnetted, 1 subnets
C 20.1.0.0 is directly connected, Loopback1 3.0.0.0/16 is subnetted, 1 subnets C 3.3.0.0 is directly connected, Serial0 2.0.0.0/16 is subnetted, 1 subnets O 2.2.0.0 [110/64] via 3.3.3.1, 00:00:48, Serial0 10.0.0.0/16 is subnetted, 1 subnets O 10.1.0.0 [110/64] via 3.3.3.1, 00:00:48, Serial0 R3#ping 10.1.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms 本文出自 “Ж孤云Ж” 博客,请务必保留此出处http://guyun.blog.51cto.com/71128/23884 本文出自 51CTO.COM技术博客 |




Ж孤云Ж
博客统计信息
热门文章
最新评论
友情链接
